Buying guide
How to Paint Metal Patio Furniture
As an Amazon Associate we earn from qualifying purchases. Our picks are researched from the manufacturers’ specifications and are our own editorial opinion.
On this page
To paint metal patio furniture, wash off the dirt and grease, sand away flaking paint and the shine, wipe the dust off, prime any bare metal, and then build the color with several thin coats of an exterior spray paint, letting each one dry before the next. Most repaints that fail do so at the prep stage, not at the paint, so most of this guide is about getting the frame ready.
The method below works for steel, wrought iron and aluminum, and for chairs, tables, bistro sets and folding chairs. If the frame is heavily rusted, the rust steps live in our guide on how to fix rusty patio furniture, and this page picks up once the metal is sound.
Which Metal Do You Have?
The metal decides the prep and the primer, so spend two minutes finding out what you own before you buy anything.
The Magnet Test
Hold a magnet to the frame. If it sticks, the frame is steel or iron, which can rust. If it does not stick, it is almost certainly aluminum, which does not rust the same way. Heavy frames with curled scrolls are often wrought iron; light frames that feel hollow and cool are usually aluminum or coated steel. Our guides to wrought iron patio furniture and aluminum patio furniture show what each looks like.
Powder Coat or Old Paint?
Most patio furniture sold today has a factory finish. Run a fingernail over a chip: a thick, hard, plastic-like layer is usually a powder coat, and a thin film that flakes is paint. The difference matters because a powder coat is slick. Hunker's guide to refinishing powder-coated furniture says you can sand the whole surface of an intact finish to remove dirt and prepare it for the new coat, and that paint will not stick to powder that has not been scuffed (Hunker).
Galvanized Steel Is an Exception
Rust-Oleum says Painter's Touch 2X Ultra Cover is not for use on galvanized steel (Rust-Oleum's technical data sheet for Painter's Touch 2X Ultra Cover sprays). If a magnet sticks but the frame has a dull, speckled gray finish, it may be galvanized, so check with the paint maker before you spray.
What You Need
The kit is short. The two items people skip, a degreaser and a primer, are the two that decide whether the paint lasts.
Paint and Primer We Would Pick
A spray can is the easiest way to get a smooth finish on mesh and scrollwork. Rust-Oleum Painter's Touch 2X Ultra Cover in Gloss Black is a general-purpose enamel for indoor and outdoor metal, and Rust-Oleum's data sheet says the line is meant for wood, metal, most plastic and wicker. For steel or iron that was already rusty, the Rust-Oleum Stops Rust Spray Paint in Semi-Gloss Black is sold as rust resistant for indoor and outdoor use. For a bronze or aged look, Rust-Oleum Universal All Surface Metallic in Oil Rubbed Bronze is an interior and exterior metallic.
How to Paint Metal Patio Furniture, Step by Step
Work outdoors or somewhere well ventilated, on a drop cloth, and plan on a dry day. Rust-Oleum says to use its sprays when temperatures are between 50 and 90°F and humidity is below 65% to ensure proper drying, and to avoid spraying in very windy and dusty conditions (Rust-Oleum's technical data sheet for Painter's Touch 2X Ultra Cover sprays).
Clean and Degrease
Remove cushions, glides and hardware, then wash the frame with warm water and a degreaser or detergent. Benjamin Moore recommends degreasing and cleaning with a power washer or damp rags and warm water (Benjamin Moore). Rinse with fresh water and let it dry completely, because paint over a damp or greasy frame will blister and peel.
Sand and Scuff
Remove loose paint and rust with a wire brush or sandpaper, and lightly sand glossy surfaces to give the new paint something to grip. That is Rust-Oleum's instruction (Rust-Oleum's technical data sheet for Painter's Touch 2X Ultra Cover sprays). Match the tool to the metal: Benjamin Moore says medium 180 to 220 grit sandpaper and a sanding sponge on aluminum, and coarse 80 grit on steel and wrought iron. Sand into the corners and curls, then wipe off every bit of dust with a damp cloth and let the frame dry.
If you scrape or sand an old painted piece, Rust-Oleum warns that old paint can contain lead, so wear a respirator rated for it, clean up with a HEPA vacuum and a wet mop, and see its data sheet for the EPA contact. Do not sand dry in a closed space.
Choose the Right Primer
Rust-Oleum says a primer gives excellent adhesion and hiding and is especially recommended for bare wood and metal (Rust-Oleum's technical data sheet for Painter's Touch 2X Ultra Cover sprays). For steel and iron, use a rust-inhibiting primer on any bare or sanded-through spots. For bare aluminum, use an etch primer, covered in the next section. A frame with a sound finish that you only scuffed may need primer only where the old finish has chipped, but a color change over a glossy factory finish is easier with a coat of primer across the whole frame.
Spray Thin Coats
Shake the can vigorously for one minute after the mixing ball begins to rattle. Rust-Oleum says to hold the can upright 10 to 16 inches from the surface, spray in a steady back-and-forth motion with a slight overlap, and apply two or more light coats a few minutes apart to avoid drips and runs (Rust-Oleum's technical data sheet for Painter's Touch 2X Ultra Cover sprays). Keep the can moving, and start each pass off the piece. Turn the furniture over and do the undersides and feet.
Rust-Oleum's sheet says the paint dries to the touch in 20 minutes and can be handled in 1 hour, based on 70°F and 50% humidity, and that you need more time when it is cooler. It gives a recoat window: apply the second coat within 1 hour, or wait until after the long window printed on your can, which the enamel sheet gives as 48 hours. Recoating in the gap between the two is how paint wrinkles.
Let It Cure
Dry to handle is not cured. Rust-Oleum says its Painter's Touch 2X sprays are fully dry in 24 hours (Rust-Oleum's technical data sheet for Painter's Touch 2X Ultra Cover sprays), and Hunker notes that a refinished frame can take up to two to three weeks to fully cure, depending on the paint (Hunker). Keep the furniture out of the rain for the first day, wait before you set heavy cushions on it, and handle it gently for the first couple of weeks.
Painting Aluminum Patio Furniture
Aluminum does not rust, but it oxidizes fast, and bare aluminum is the hardest metal for paint to grip. PPG's refinish guidance says to prime or chemically treat bare aluminum immediately, and that oxidation can form on exposed aluminum surfaces in as little as 15 minutes, with a re-sand if needed (PPG).
Use a Self-Etching Primer
PPG lists an etch primer as the first of three ways to treat bare aluminum (PPG). A spray version is the practical choice for furniture: Rust-Oleum Automotive Self Etching Primer Spray is sold for bare metal and aluminum. Hunker's aluminum furniture guide applies one thin coat of self-etching primer from about 8 inches away, lets it dry fully, lightly sands it with 400 grit and wipes with a tack cloth (Hunker). Follow the can, since each product has its own dry time and topcoat window.
Sand Aluminum Gently
Benjamin Moore says 180 to 220 grit on aluminum, with no wire brush (Benjamin Moore). The PPG page, written for auto-body refinishing, says not to use the same sandpaper on steel and aluminum, to avoid galvanic corrosion. Use paper you keep for aluminum only.
Topcoat
After the primer, finish with an exterior enamel in thin coats. Hunker recommends exterior-grade enamel spray paint and avoiding high gloss, since shine shows imperfections, and a sealer after the paint (Hunker). If you want a color change on a mesh or slatted aluminum chair, spray from several angles so the paint reaches both sides of every slat.
Painting Over Rust?
A little surface rust on an otherwise sound frame is fine to repaint after you clean and sand it: Benjamin Moore says light rust needs only cleaning and sanding, while heavy rust must be primed after cleaning and sanding to seal the surface (Benjamin Moore). Do not paint over flaking rust. Our guide on how to fix rusty patio furniture walks through brushing, treating and priming rusty steel and iron, then come back here for the color coats.
Spray Paint or Brush?
Spray gives the smoother finish on most patio furniture, and brush gives you control on small repairs.
Why Spray Wins on Most Pieces
Benjamin Moore says spraying is the most efficient method, especially on furniture with mesh detail (Benjamin Moore). A light spray coat reaches every slat and curl without brush marks.
When a Brush Is Better
Use a brush for touch-ups and for tight places the spray cannot reach cleanly. Benjamin Moore suggests a paintbrush or a fine-finish 4 or 6 inch roller for fine details and hard-to-reach areas. If you brush, use paint made to be brushed, because the thin spray formulas do not level well from a brush.
Making the Paint Last
A good paint job fails slowly, at the chips and the places water sits. A few habits stretch it out.
Cover the Furniture
A fitted, breathable cover keeps rain and leaf litter off the finish. Our guide to the best patio furniture covers compares options, and our guide on how to store patio furniture has the winter routine.
Wash Gently
Clean the frame with mild soap and water and a soft cloth, not abrasive pads. Our guide to cleaning patio furniture has the method, and it avoids the harsh cleaners that dull a fresh finish.
Touch Up Early
Keep a small can of the color and a little primer. A chip touched up the week it happens takes minutes, and a chip left to the winter becomes rust that lifts the paint around it.
Quick Reference: Metal by Metal
| Steel and wrought iron | Aluminum | Powder-coated | |
|---|---|---|---|
| Sanding | Coarse 80 grit and a wire brush (Benjamin Moore) | 180 to 220 grit, no wire brush (Benjamin Moore) | Scuff the whole surface (Hunker) |
| Primer | Rust-inhibiting primer on bare spots | Etch primer straight away (PPG) | Primer recommended on a color change (Hunker) |
| Watch for | Rust under the paint | Fast oxidation of bare metal | Slick, unscuffed finish |
❓ Frequently Asked Questions
Sources
Rust-Oleum, Painter's Touch Ultra Cover 2X Enamel Sprays and 2X Ultra Cover Satin Sprays technical data sheets; Benjamin Moore, How to Paint Metal Furniture; PPG, Metal Surface Prep: Bare Aluminum; Hunker, How To Paint Aluminum Patio Furniture and How To Refinish Powder-Coated Patio Furniture. Temperatures, times and grits above come from these pages and from the label on your own can, which always wins.
Related: How to fix rusty patio furniture · Best aluminum patio furniture · Best wrought iron patio furniture · Best patio furniture covers · How to clean patio furniture