Buying guide
Best Outdoor Cushion Foam 2026
As an Amazon Associate we earn from qualifying purchases. Our picks are researched from the manufacturers’ specifications and are our own editorial opinion.
On this page
The best outdoor cushion foam for most patios is dry fast foam, also called reticulated foam, because its open cells let rain drain through instead of soaking in. If your seats sit under a roof or in a cover that keeps water out, high density polyurethane foam is the standard upholstery choice. This page is about the foam inside the cushion. If you would rather buy cushions that are already made, see our guide to the best outdoor cushions.
Which Foam Is Best for Outdoor Cushions?
Dry fast foam is the best choice where rain reaches the cushions, and high density foam is the best choice where it does not. The Foam Factory explains why: water and air pass easily through dry fast foam, so it does not hold water and dries quickly, while conventional foam holds water through capillary action, which can lead to rot, mold and mildew. The trade-off is feel: The Foam Factory calls dry fast a fairly rigid foam.
Neither type is waterproof. In a reply under its own article, The Foam Factory says that if the foam gets wet it becomes saturated and takes time to dry out. Its job is to drain and dry quickly, not to repel water. Our guide on how to wash outdoor cushions has a section on foam fill and quick-dry foam if you are cleaning cushions you already own.
Types of Outdoor Foam
Dry Fast (Reticulated) Foam
Reticulated foam is open-cell foam with the cell walls removed, leaving a skeleton of interconnected struts. The Foam Factory says its cells can reach about 5 mm, against fractions of a millimeter in traditional open-cell polyurethane. Typical uses include patio and wicker chair cushions, pool furniture, outdoor benches and boat cushions. The Foam Factory reports a useful life of around 5 to 7 years, and manufacturer listings below claim longer.
High Density Polyurethane
High density polyurethane is the standard upholstery foam. The Polyurethane Foam Association says density affects durability and support: the higher the polymer density, the better the foam keeps its properties over time. It is a good fit for porch and sunroom seating, or for patio cushions that come in under cover when it rains.
Polyfill
Polyfill is loose polyester fiber, the soft fill in many cheap throw pillows and back cushions. It is lighter and plusher than foam but gives less support, so it suits back cushions more than seats. We do not list polyfill products here because this page is about foam inserts.
Marine Foam
Marine foam is the label sellers use for foam meant for boat seats. The Foam Factory lists boat cushions among the common uses of dry fast foam, and the FoamRush listing below calls the same foam “marine foam.” In practice, marine foam for seats means a water-draining reticulated foam, usually with a marine or outdoor fabric over it.
Best Outdoor Cushion Foam Reviewed
Specifications below come from each product listing, so check the exact size and firmness before you order. All five are sold as foam only: no cover is included.
| Dry Fast Foam | FoamRush 3 in Dry Fast EDITOR’S CHOICE | FoamRush 2 in 4 Pack | AK Trading DryFast 4 in |
|---|---|---|---|
| Image | | | |
| Foam type | Dry fast, open cell reticulated | Dry fast, open cell reticulated | Dry fast, reticulated |
| Size | 3 x 18 x 72 in | 2 x 24 x 72 in, 4 sheets | 4 x 24 x 72 in |
| Firmness (listing) | 33 lb IFD | 37 lb IFD | Not stated |
| Density (listing) | 1.8 lb per cu ft | 1.8 lb per cu ft | Not stated |
| Availability | Shop Now at Amazon | Shop Now at Amazon | Shop Now at Amazon |
EDITOR’S CHOICE
FoamRush 3 in Dry Fast
- Foam type
- Dry fast, open cell reticulated
- Size
- 3 x 18 x 72 in
Show specificationsHide specifications
- Firmness (listing)
- 33 lb IFD
- Density (listing)
- 1.8 lb per cu ft
FoamRush 2 in 4 Pack
- Foam type
- Dry fast, open cell reticulated
- Size
- 2 x 24 x 72 in, 4 sheets
Show specificationsHide specifications
- Firmness (listing)
- 37 lb IFD
- Density (listing)
- 1.8 lb per cu ft
AK Trading DryFast 4 in
- Foam type
- Dry fast, reticulated
- Size
- 4 x 24 x 72 in
Show specificationsHide specifications
- Firmness (listing)
- Not stated
- Density (listing)
- Not stated
| High Density Foam | GoTo Foam 3 in 44 ILD | FoammaUSA 4 in |
|---|---|---|
| Image | | |
| Foam type | High density polyurethane | High density polyurethane |
| Size | 3 x 24 x 72 in | 4 x 24 x 24 in |
| Firmness (listing) | 44 lb ILD, firm | 44 lb compression |
| Density (listing) | 1.8 | 1.8 |
| Availability | Shop Now at Amazon | Shop Now at Amazon |
GoTo Foam 3 in 44 ILD
- Foam type
- High density polyurethane
- Size
- 3 x 24 x 72 in
Show specificationsHide specifications
- Firmness (listing)
- 44 lb ILD, firm
- Density (listing)
- 1.8
FoammaUSA 4 in
- Foam type
- High density polyurethane
- Size
- 4 x 24 x 24 in
Show specificationsHide specifications
- Firmness (listing)
- 44 lb compression
- Density (listing)
- 1.8
Best Dry Fast Outdoor Cushion Foam
These are the picks for cushions that stay out in the weather. Each is reticulated foam sold as a plain sheet, so you cut it to the size of your cover.
FoamRush 3 x 18 x 72 in Dry Fast Outdoor Foam
FoamRush makes this open cell, reticulated foam in the USA and sells it as a 3 x 18 x 72 in sheet. The listing gives a density of 1.8 pounds per cubic foot and a 33 pound IFD, a firm but not rock-hard feel, and says the pores let water and air pass through. The sheet is 3 in thick, a common depth for a seat cushion, and the 72 in length cuts into two chair seats or one long bench cushion.
✅ Pros
- Reticulated foam that drains and dries quickly, per the listing
- A 33 pound IFD, softer than the 37 pound foam in the same brand’s 2 in pack
- Thick enough for a comfortable chair seat
❌ Cons
- Only 18 in wide, so wide seats need two pieces or a different size
- Foam only: you still need a cover
Best For: most patio chair and bench cushions that get rained on.
FoamRush 2 in Dry Fast Outdoor Foam, 24 x 72 in, 4 Pack
This pack holds four 2 in thick sheets, each 24 x 72 in, of the same open cell reticulated foam. The listing gives 1.8 pound density and a 37 pound IFD, so it feels firmer than the 3 in sheet. It is the practical choice when you have a whole set to refill, or when you want to stack two layers to build a thicker seat.
✅ Pros
- Four full-size sheets in one box
- Drains and airs out, per the listing
- Firmer 37 pound IFD for a supportive seat
❌ Cons
- 2 in is thin for a seat on its own
- More foam than a single chair needs
Best For: a full patio set, or building up seat depth in layers.
AK Trading DryFast Foam, 4 x 24 x 72 in
AK Trading sells this 4 in thick, 24 x 72 in sheet of dry fast foam, cut from a reticulated, open cell block. The listing says the large open pores permit maximum water drainage and air circulation, that the foam has built-in antimicrobial protection against common molds and mildews, and that it can be cleaned with a light hose down. It also claims that 120,000 stress cycles cause only a 5 percent reduction in volume.
✅ Pros
- 4 in thickness for deeper sofa and lounge seats
- Hose-clean, per the listing
- Antimicrobial protection, per the listing
❌ Cons
- The listing gives no IFD or density to compare
- One big slab, so it takes more cutting than a precut block
Best For: deeper seats where thickness matters more than the firmness number.
Best High Density Outdoor Cushion Foam
High density foam works outdoors only when the cushion cover keeps the rain out or the cushions come in when the weather turns. Both of these are plain polyurethane, not water-draining foam.
GoTo Foam 3 x 24 x 72 in, 44 ILD
GoTo Foam makes this slab in the USA and lists it as CertiPUR-US certified, with a density of 1.8 and a 44 pound firm ILD. It is sold as general upholstery foam, and the listing does not describe it as water-draining, so treat it as foam for covered seating. At 24 x 72 in and 3 in thick it cuts into several seat cushions.
✅ Pros
- Firm 44 ILD for a supportive seat
- CertiPUR-US certified, per the listing
- Large 24 x 72 in size for cutting
❌ Cons
- Not sold as water-draining foam
- Needs a waterproof or sheltered setup
Best For: covered porches, sunrooms and cushions you bring in when it rains.
FoammaUSA 4 x 24 x 24 in Outdoor Foam Replacement
FoammaUSA sells this 4 in thick, 24 x 24 in block as an outdoor foam cushion replacement. The listing gives a 1.8 high density, a 44 pound compression rate and CertiPUR-US certification, claims 7 to 10 years of support, and says custom cuts are available. It is precut, which saves you the cutting if your seat is a standard square.
✅ Pros
- Precut square, ready for a standard seat
- Firm 44 pound support
- CertiPUR-US certified, per the listing
❌ Cons
- Not described as water-draining
- Fixed 24 x 24 in footprint
Best For: square patio seats that sit under cover.
How to Choose Outdoor Cushion Foam
Thickness
Thicker foam gives a deeper, softer-feeling seat and more room to settle. Pick the thickness the cover was cut for, since a cushion cover that is too slack looks sloppy and one that is too tight is hard to zip. Dining and bistro chairs usually take thinner foam than a deep seating sofa, and our listings above run from 2 to 4 in.
Firmness: IFD and ILD
The Polyurethane Foam Association defines IFD as the force in pounds needed to indent a foam sample 25 percent of its original height. The more force it takes, the firmer the foam, and the association says flexible foam IFD runs from about 5 pounds, supersoft, to about 80 pounds, very firm. ILD means the same measurement, and sellers use both names. The association also notes that firmness is independent of density: a high density foam can be soft, and a low density foam can be firm.
Cutting to Size
Foam is easy to cut with a long serrated knife or an electric carving knife. Trace the cover’s seam outline onto the foam with a marker, cut a touch larger than the line so the corners fill out, and cut slowly with the blade held straight. If you do not want to cut, some sellers offer custom cuts, as FoammaUSA’s listing notes.
The Cover
Foam does most of its job under a cover that suits it. The Foam Factory says dry fast foam is usually used with a covering and recommends waterproof, breathable outdoor fabrics such as Phifertex or Sunbrella. Our guide to the best outdoor cushion covers compares replacement covers by fabric and fit.
How to Replace the Foam in Outdoor Cushions
Replacing foam is a half-hour job once the new foam has expanded.
- Measure the cover. Lay the empty cover flat and measure length, width and depth across the seams. Do not trust the old foam, which has compressed.
- Let new foam expand. Foam ships compressed. The FoamRush listing says to allow 1 to 7 days for it to expand.
- Trace and cut. Mark the foam from the cover’s measurements and cut it with a serrated or electric carving knife.
- Squeeze it in. Fold the foam, ease it into the cover, then unfold it and push the corners into place. A plastic bag over the foam helps it slide in; remove the bag once inside.
- Zip and fluff. Close the cover, smooth out the seams and sit on the seat for a day before you judge the fit.
Keeping Foam Dry
Covers and Storage
Even drainage-friendly foam lasts longer if it spends less time wet. Store cushions out of the rain and let them air out after storms. If the foam does get soaked, The Foam Factory says dry fast foam typically dries within a day outdoors. Our guide on how to store patio furniture covers winter storage, and you can stop loose seats from blowing off in the wind with the fixes in how to keep outdoor cushions from blowing away.
Cleaning Foam
The Foam Factory says dry fast foam can be rinsed with a hose, and that water carries dirt out through its open cells. For ordinary polyurethane, avoid soaking the block. Spot-clean the cover, and let the foam dry thoroughly before it goes back in.
Frequently Asked Questions
Keep reading: Best Outdoor Cushions · Best Outdoor Cushion Covers · How to Wash Outdoor Cushions · How to Keep Outdoor Cushions From Blowing Away · How to Store Patio Furniture